[Linux-stm32] [PATCH V2 17/22] ARM: dts: stm32: Enable Bluetooth on AV96

[Manivannan Sadhasivam]

On Tue, Mar 31, 2020 at 02:56:56AM +0200, Marek Vasut wrote:
> The WiFi/Bluetooth chip is attached to USART2 on AV96 as well, describe
> it in DT to make it available. Remove BT LED and turn it into a shutdown
> GPIO, because the GPIO line controls the BT_REG_ON signal. The LED is just
> an indicator connected to the same line, but not the primary function.
> 
> Signed-off-by: Marek Vasut <marex at denx.de>

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>

Thanks,
Mani

> Cc: Alexandre Torgue <alexandre.torgue at st.com>
> Cc: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
> Cc: Maxime Coquelin <mcoquelin.stm32 at gmail.com>
> Cc: Patrice Chotard <patrice.chotard at st.com>
> Cc: Patrick Delaunay <patrick.delaunay at st.com>
> Cc: linux-stm32 at st-md-mailman.stormreply.com
> To: linux-arm-kernel at lists.infradead.org
> ---
> V2: No change
> ---
>  arch/arm/boot/dts/stm32mp157a-avenger96.dts | 23 ++++++++++++++-------
>  1 file changed, 16 insertions(+), 7 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> index 12ee95d5adb1..29af5ed2ebb3 100644
> --- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> @@ -21,6 +21,7 @@ aliases {
>  		mmc0 = &sdmmc1;
>  		serial0 = &uart4;
>  		serial1 = &uart7;
> +		serial2 = &usart2;
>  		spi0 = &qspi;
>  	};
>  
> @@ -63,13 +64,6 @@ led4 {
>  			default-state = "off";
>  			panic-indicator;
>  		};
> -
> -		led5 {
> -			label = "blue:bt";
> -			gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
> -			linux,default-trigger = "bluetooth-power";
> -			default-state = "off";
> -		};
>  	};
>  
>  	sd_switch: regulator-sd_switch {
> @@ -421,3 +415,18 @@ &uart7 {
>  	pinctrl-0 = <&uart7_pins_a>;
>  	status = "okay";
>  };
> +
> +/* Bluetooth */
> +&usart2 {
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&usart2_pins_a>;
> +	pinctrl-1 = <&usart2_sleep_pins_a>;
> +	st,hw-flow-ctrl;
> +	status = "okay";
> +
> +	bluetooth {
> +		compatible = "brcm,bcm43438-bt";
> +		max-speed = <3000000>;
> +		shutdown-gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
> +	};
> +};
> -- 
> 2.25.1
>