[Linux-stm32] FW: STM32MP157c Mainline linux boot
Patrick DELAUNAY
patrick.delaunay at foss.st.com
Tue Dec 8 11:02:43 UTC 2020
Alexandre,
For Mainline Linux:
earlyprintk console=ttyS3,115200 is this console option correct?
Please can you confirm, I think that ttyS3 (used for OpenSTLinux v1.X)
must be replacde by ttySTM0 for linux boot args?
Patrick
On 12/8/20 11:53 AM, Patrick DELAUNAY wrote:
>
> -----Original Message-----
> From: Jagan Teki <jagan at amarulasolutions.com>
> Sent: mardi 8 décembre 2020 10:26
> To: Patrick DELAUNAY <patrick.delaunay at st.com>
> Subject: Re: STM32MP157c Mainline linux boot
>
> Hi Patrick,
>
> Still, something missed from my end.
>
> earlyprintk console=ttyS3,115200 is this console option correct?
>
> I can see it is hangup while enumerating uart console it seems, I have enabled CONFIG_STM32MP1_DEBUG_UART, CONFIG_EARLY_PRINTK and dts aliased with serial0 as uart4 aliases {
> serial0 = &uart4;
> };
>
> Log:
> STM32MP> ext4load mmc 0:4 $kernel_addr_r zImage;ext4load mmc 0:4
> $fdt_addr_r stm32mp157c-icore-stm32mp1-edimm2.2
> .dtb;setenv bootargs root=/dev/mmcblk0p4 rootwait rw earlyprintk console=ttyS3,115200;bootz $kernel_addr_r - $fd t_addr_r
> 9658880 bytes read in 2058 ms (4.5 MiB/s)
> 52701 bytes read in 34 ms (1.5 MiB/s)
> ## Flattened Device Tree blob at c4000000
> Booting using the fdt blob at 0xc4000000
> Loading Device Tree to cfff0000, end cffffddc ... OK
>
> Starting kernel ...
>
> [ 0.000000] Booting Linux on physical CPU 0x0
> [ 0.000000] Linux version
> 5.10.0-rc6-next-20201203-00001-g91f452399c24-dirty (ub at ub-XPS-13-9350) (arm-buildro ot-linux-gnueabihf-gcc.br_real (Buildroot
> 2020.08-849-gdcd4b75069-dirty) 9.3.0, GNU ld (GNU Binutils) 2.34) #1 S MP Tue Dec 8 13:41:37 IST 2020
> [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
> [ 0.000000] CPU: div instructions available: patching division code
> [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
> instruction cache
> [ 0.000000] OF: fdt: Machine model: Engicam i.Core STM32MP1
> EDIMM2.2 Starter Kit
> [ 0.000000] printk: bootconsole [earlycon0] enabled
> [ 0.000000] Memory policy: Data cache writealloc
> [ 0.000000] efi: UEFI not found.
> [ 0.000000] Reserved memory: created DMA memory pool at 0x10000000,
> size 0 MiB
> [ 0.000000] OF: reserved mem: initialized node mcuram2 at 10000000,
> compatible id shared-dma-pool
> [ 0.000000] Reserved memory: created DMA memory pool at 0x10040000,
> size 0 MiB
> [ 0.000000] OF: reserved mem: initialized node
> vdev0vring0 at 10040000, compatible id shared-dma-pool
> [ 0.000000] Reserved memory: created DMA memory pool at 0x10041000,
> size 0 MiB
> [ 0.000000] OF: reserved mem: initialized node
> vdev0vring1 at 10041000, compatible id shared-dma-pool
> [ 0.000000] Reserved memory: created DMA memory pool at 0x10042000,
> size 0 MiB
> [ 0.000000] OF: reserved mem: initialized node
> vdev0buffer at 10042000, compatible id shared-dma-pool
> [ 0.000000] Reserved memory: created DMA memory pool at 0x30000000,
> size 0 MiB
> [ 0.000000] OF: reserved mem: initialized node mcuram at 30000000,
> compatible id shared-dma-pool
> [ 0.000000] Reserved memory: created DMA memory pool at 0x38000000,
> size 0 MiB
> [ 0.000000] OF: reserved mem: initialized node retram at 38000000,
> compatible id shared-dma-pool
> [ 0.000000] cma: Reserved 64 MiB at 0xdc000000
> [ 0.000000] Zone ranges:
> [ 0.000000] DMA [mem 0x00000000c0000000-0x00000000dfffffff]
> [ 0.000000] Normal empty
> [ 0.000000] HighMem empty
> [ 0.000000] Movable zone start for each node
> [ 0.000000] Early memory node ranges
> [ 0.000000] node 0: [mem 0x00000000c0000000-0x00000000dfffffff]
> [ 0.000000] Initmem setup node 0 [mem 0x00000000c0000000-0x00000000dfffffff]
> [ 0.000000] psci: probing for conduit method from DT.
> [ 0.000000] psci: PSCIv1.0 detected in firmware.
> [ 0.000000] psci: Using standard PSCI v0.2 function IDs
> [ 0.000000] psci: Trusted OS migration not required
> [ 0.000000] psci: SMC Calling Convention v1.0
> [ 0.000000] percpu: Embedded 20 pages/cpu s49996 r8192 d23732 u81920
> [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048
> [ 0.000000] Kernel command line: root=/dev/mmcblk0p4 rootwait rw
> earlyprintk console=ttyS3,115200
> [ 0.000000] Dentry cache hash table entries: 65536 (order: 6,
> 262144 bytes, linear)
> [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072
> bytes, linear)
> [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
> [ 0.000000] Memory: 429616K/524288K available (13312K kernel code,
> 2181K rwdata, 5280K rodata, 2048K init, 40 1K bss, 29136K reserved, 65536K cma-reserved, 0K highmem)
> [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
> [ 0.000000] rcu: Hierarchical RCU implementation.
> [ 0.000000] rcu: RCU event tracing is enabled.
> [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2.
> [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay
> is 10 jiffies.
> [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
> [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
> [ 0.000000] random: get_random_bytes called from
> start_kernel+0x3cc/0x564 with crng_init=0
> [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt).
> [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff
> max_cycles: 0x588fe9dc0, max_idle_ns: 44079
> 5202592 ns
> [ 0.000010] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps
> every 4398046511097ns
> [ 0.008119] Switching to timer-based delay loop, resolution 41ns
> [ 0.026216] Console: colour dummy device 80x30
> [ 0.030774] Calibrating delay loop (skipped), value calculated
> using timer frequency.. 48.00 BogoMIPS (lpj=24
> 0000)
> [ 0.041294] pid_max: default: 32768 minimum: 301
> [ 0.046174] Mount-cache hash table entries: 1024 (order: 0, 4096
> bytes, linear)
> [ 0.053607] Mountpoint-cache hash table entries: 1024 (order: 0,
> 4096 bytes, linear)
> [ 0.062356] CPU: Testing write buffer coherency: ok
> [ 0.067697] CPU0: update cpu_capacity 1024
> [ 0.071855] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
> [ 0.078389] Setting up static identity map for 0xc0300000 - 0xc03000ac
> [ 0.088390] rcu: Hierarchical SRCU implementation.
> [ 0.101127] EFI services will not be available.
> [ 0.106051] smp: Bringing up secondary CPUs ...
> [ 0.111449] CPU1: update cpu_capacity 1024
> [ 0.111461] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
> [ 0.111667] smp: Brought up 1 node, 2 CPUs
> [ 0.125739] SMP: Total of 2 processors activated (96.00 BogoMIPS).
> [ 0.132014] CPU: All CPU(s) started in SVC mode.
> [ 0.137505] devtmpfs: initialized
> [ 0.159460] VFP support v0.3: implementor 41 architecture 2 part 30
> variant 7 rev 5
> [ 0.167622] clocksource: jiffies: mask: 0xffffffff max_cycles:
> 0xffffffff, max_idle_ns: 19112604462750000 ns
> [ 0.177623] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
> [ 0.187542] pinctrl core: initialized pinctrl subsystem
> [ 0.196090] DMI not present or invalid.
> [ 0.200523] NET: Registered protocol family 16
> [ 0.208090] DMA: preallocated 256 KiB pool for atomic coherent allocations
> [ 0.219608] thermal_sys: Registered thermal governor 'step_wise'
> [ 0.219983] cpuidle: using governor menu
> [ 0.230428] No ATAGs?
> [ 0.232859] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4
> watchpoint registers.
> [ 0.241016] hw-breakpoint: maximum watchpoint size is 8 bytes.
> [ 0.251971] Serial: AMBA PL011 UART driver
> [ 0.290080] /soc/interrupt-controller at 5000d000: bank0
> [ 0.295270] /soc/interrupt-controller at 5000d000: bank1
> [ 0.300392] /soc/interrupt-controller at 5000d000: bank2
> [ 0.309097] stm32mp157-pinctrl soc:pin-controller at 50002000: GPIOA bank added
> [ 0.316697] stm32mp157-pinctrl soc:pin-controller at 50002000: GPIOB bank added
> [ 0.324206] stm32mp157-pinctrl soc:pin-controller at 50002000: GPIOC bank added
> [ 0.331737] stm32mp157-pinctrl soc:pin-controller at 50002000: GPIOD bank added
> [ 0.339214] stm32mp157-pinctrl soc:pin-controller at 50002000: GPIOE bank added
> [ 0.346755] stm32mp157-pinctrl soc:pin-controller at 50002000: GPIOF bank added
> [ 0.354235] stm32mp157-pinctrl soc:pin-controller at 50002000: GPIOG bank added
> [ 0.361741] stm32mp157-pinctrl soc:pin-controller at 50002000: GPIOH bank added
> [ 0.369215] stm32mp157-pinctrl soc:pin-controller at 50002000: GPIOI bank added
> [ 0.376737] stm32mp157-pinctrl soc:pin-controller at 50002000: GPIOJ bank added
> [ 0.384212] stm32mp157-pinctrl soc:pin-controller at 50002000: GPIOK bank added
> [ 0.391548] stm32mp157-pinctrl soc:pin-controller at 50002000: Pinctrl
> STM32 initialized
> [ 0.400793] stm32mp157-pinctrl soc:pin-controller-z at 54004000: GPIOZ
> bank added
> [ 0.408173] stm32mp157-pinctrl soc:pin-controller-z at 54004000:
> Pinctrl STM32 initialized
> [ 0.443287] AT91: Could not find identification node
> [ 0.445783] vtt_ddr: supplied by vdd
> [ 0.455092] vref_ddr: supplied by vdd
> [ 0.460017] v2v8: supplied by v3v3
> [ 0.464097] v1v8: supplied by v3v3
> [ 0.469830] iommu: Default domain type: Translated
> [ 0.475220] vgaarb: loaded
> [ 0.479043] SCSI subsystem initialized
> [ 0.483544] usbcore: registered new interface driver usbfs
> [ 0.489303] usbcore: registered new interface driver hub
> [ 0.494749] usbcore: registered new device driver usb
> [ 0.501305] pps_core: LinuxPPS API ver. 1 registered
> [ 0.506340] pps_core: Software ver. 5.3.6 - Copyright 2005-2007
> Rodolfo Giometti <giometti at linux.it>
> [ 0.515647] PTP clock support registered
> [ 0.523314] clocksource: Switched to clocksource arch_sys_counter
> [ 1.948309] NET: Registered protocol family 2
> [ 1.953753] tcp_listen_portaddr_hash hash table entries: 512
> (order: 0, 6144 bytes, linear)
> [ 1.962249] TCP established hash table entries: 4096 (order: 2,
> 16384 bytes, linear)
> [ 1.970191] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
> [ 1.977521] TCP: Hash tables configured (established 4096 bind 4096)
> [ 1.984156] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
> [ 1.990799] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
> [ 1.998132] NET: Registered protocol family 1
> [ 2.003428] RPC: Registered named UNIX socket transport module.
> [ 2.009436] RPC: Registered udp transport module.
> [ 2.014241] RPC: Registered tcp transport module.
> [ 2.019004] RPC: Registered tcp NFSv4.1 backchannel transport module.
> [ 2.025552] PCI: CLS 0 bytes, default 64
> [ 2.030836] hw perfevents: enabled with armv7_cortex_a7 PMU driver,
> 5 counters available
> [ 2.040759] Initialise system trusted keyrings
> [ 2.045735] workingset: timestamp_bits=30 max_order=17 bucket_order=0
> [ 2.061599] squashfs: version 4.0 (2009/01/31) Phillip Lougher
> [ 2.068791] NFS: Registering the id_resolver key type
> [ 2.074014] Key type id_resolver registered
> [ 2.078251] Key type id_legacy registered
> [ 2.082467] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
> [ 2.089362] ntfs: driver 2.1.32 [Flags: R/O].
> [ 2.094483] Key type asymmetric registered
> [ 2.098640] Asymmetric key parser 'x509' registered
> [ 2.103705] Block layer SCSI generic (bsg) driver version 0.4
> loaded (major 247)
> [ 2.111198] io scheduler mq-deadline registered
> [ 2.115815] io scheduler kyber registered
> [ 2.150556] reg11: supplied by vdd
> [ 2.154448] reg18: supplied by vdd
> [ 2.158196] usb33: supplied by regulator-dummy
> [ 2.234829] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
> [ 2.246020] SuperH (H)SCI(F) driver initialized
> [ 2.251634] msm_serial: driver initialized
> [ 2.256079] STMicroelectronics ASC driver initialized
> [ 2.263194] STM32 USART driver initialized
> [ 2.268088] 40010000.serial: ttySTM0 at MMIO 0x40010000 (irq = 30,
> base_baud = 4000000) is a stm32-usart
>
> On Mon, Dec 7, 2020 at 1:51 AM Jagan Teki <jagan at amarulasolutions.com> wrote:
>> Hi Patrick,
>>
>> Got fixed, with DEBUG_LL
>>
>> Thanks.
>>
>> On Sat, Dec 5, 2020 at 12:49 AM Jagan Teki <jagan at amarulasolutions.com> wrote:
>>> Hi Patrick,
>>>
>>> Did you boot the Mainline linux recently? I'm trying to boot
>>> STM32MP157C based design board with mainline Linux by using
>>> multi_v7_defconfig.
>>>
>>> Here is the boot log, might be an issue with earlycon issue or
>>> something. The Linux console on the design at uart4 and I have
>>> aliased to serial0 with is done via chosen node.
>>>
>>> STM32MP-i.Core> ext4load mmc 0:4 $kernel_addr_r zImage;ext4load mmc
>>> 0:4 $fdt_addr_r stm32mp157c-icore-stm32mp1.dtb;setenv bootargs
>>> earlyprintk consol
>>> e=ttySTM0,115200 root=/dev/mmcblk0p4 rootwait rw;bootz
>>> $kernel_addr_r
>>> - $fdt_addr_r
>>> 7463424 bytes read in 494 ms (14.4 MiB/s)
>>> 60673 bytes read in 5 ms (11.6 MiB/s) Kernel image @ 0xc2000000 [
>>> 0x000000 - 0x71e200 ] ## Flattened Device Tree blob at c4000000
>>> Booting using the fdt blob at 0xc4000000
>>> Using Device Tree in place at c4000000, end c4011d00
>>>
>>> Starting kernel ...
>>>
>>> Any help?
>>>
>>> Jagan.
>>>
>>> --
>>> Jagan Teki,
>>> Amarula Solutions India Pvt. Ltd.
>>> Co-Founder & Embedded Linux Architect 405/E-Block, Sri Lakshmi
>>> Shubham Arcade, Chandanagar, Hyderabad - 500050, India M. (+91) 910
>>> 009 0959 [`as] http://www.amarulasolutions.com
>>
>>
>> --
>> Jagan Teki,
>> Amarula Solutions India Pvt. Ltd.
>> Co-Founder & Embedded Linux Architect
>> 405/E-Block, Sri Lakshmi Shubham Arcade, Chandanagar, Hyderabad - 500050, India
>> M. (+91) 910 009 0959
>> [`as] http://www.amarulasolutions.com
>
>
More information about the Linux-stm32
mailing list