[Linux-stm32] [PATCH v4 03/13] dt-bindings: net: Add a YAML schemas for the generic MDIO options

[Rob Herring]

On Thu, Jun 27, 2019 at 9:32 AM Maxime Ripard <maxime.ripard at bootlin.com> wrote:
>
> The MDIO buses have a number of available device tree properties that can
> be used in their device tree node. Add a YAML schemas for those.
>
> Suggested-by: Andrew Lunn <andrew at lunn.ch>
> Signed-off-by: Maxime Ripard <maxime.ripard at bootlin.com>
> ---
>  Documentation/devicetree/bindings/net/mdio.txt  | 38 +-------------
>  Documentation/devicetree/bindings/net/mdio.yaml | 51 ++++++++++++++++++-
>  2 files changed, 52 insertions(+), 37 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/net/mdio.yaml

Reviewed-by: Rob Herring <robh at kernel.org>

However, some comments for a follow-up...

> diff --git a/Documentation/devicetree/bindings/net/mdio.yaml b/Documentation/devicetree/bindings/net/mdio.yaml
> new file mode 100644
> index 000000000000..b8fa8251c4bc
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/mdio.yaml
> @@ -0,0 +1,51 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/net/mdio.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: MDIO Bus Generic Binding
> +
> +maintainers:
> +  - Andrew Lunn <andrew at lunn.ch>
> +  - Florian Fainelli <f.fainelli at gmail.com>
> +  - Heiner Kallweit <hkallweit1 at gmail.com>
> +
> +description:
> +  These are generic properties that can apply to any MDIO bus. Any
> +  MDIO bus must have a list of child nodes, one per device on the
> +  bus. These should follow the generic ethernet-phy.yaml document, or
> +  a device specific binding document.
> +
> +properties:
> +  reset-gpios:
> +    maxItems: 1
> +    description:
> +      The phandle and specifier for the GPIO that controls the RESET
> +      lines of all PHYs on that MDIO bus.
> +
> +  reset-delay-us:
> +    description:
> +      RESET pulse width in microseconds. It applies to all PHY devices
> +      and must therefore be appropriately determined based on all PHY
> +      requirements (maximum value of all per-PHY RESET pulse widths).
> +
> +examples:
> +  - |
> +    davinci_mdio: mdio at 5c030000 {

Can we enforce nodename to be mdio? That may not work for muxes.
You'll probably have to implement it and see.

> +        compatible = "ti,davinci_mdio";
> +        reg = <0x5c030000 0x1000>;
> +        #address-cells = <1>;
> +        #size-cells = <0>;

These 2 should have a schema.

> +
> +        reset-gpios = <&gpio2 5 1>;
> +        reset-delay-us = <2>;
> +
> +        ethphy0: ethernet-phy at 1 {
> +            reg = <1>;

Need a child node schema to validate the unit-address and reg property.

> +        };
> +
> +        ethphy1: ethernet-phy at 3 {
> +            reg = <3>;
> +        };
> +    };
> --
> git-series 0.9.1